Sanwood is a direct factory which has specialized in manufacturing Thermal Shock Test Chamber,Thermal Shock Chamber,Two-zone Thermal Shock Test Chamber,Two-zone Thermal Shock Chamber,Three-zone Thermal Shock Test Chamber for 23 years.
Outer wall: Double-sided galvanized steel, surface spray treatment (SANWOOD standard color)
External structural reinforcement: Double-sided galvanized steel, surface spray
treatment or Q235 steel, surface pickling, phosphating, surface spray treatment
Inner wall: SUS304 stainless steel plate (1.2mm thick)
Internal structural reinforcement: SUS304 stainless steel
Insulation material: rigid polyurethane foam + ultra-fine glass fiber + high temperature cotton
Chamber bottom bearing capacity: 100kg/m2 (uniform load)
The total load capacity ( base plate and sample holder) in the chamber does not exceed 120kg
Thermal shock test chamber Briefly introduction:
Thermal shock test chamber system structure can be divided into two parts. Namely, high temperature tank (preheating zone), cryogenic tank (pre-cooling zone).
Thermal shock test chamber Testing principle
Two-zone Thermal Shock Test Chamber Testing principle mainly through controlling the portable basket (test samples District) to quickly move between cryogenic tank and high temperature tank to achieve rapid thermal shock test. The whole testing process test samples along with mobile gondola to move together. The test chaber is suitable for the examination of the whole set of products, components, parts and materials subjected to rapid changes in temperature. The temperature impact test chamber are used in a shortest time to evaluate the test samples due to thermal expansion and contraction caused by the changes of chemical or physical damage.
The advantages of SANWOOD Thermal shock test chamber
1.Two-zone Thermal Shock Chamber Temperature and humidity setting protection
2.Three-zone Thermal Shock Test Chamber. Air pressure driven test area(sample)
3.Error failure medical record table cartilage device
4.HFC environmentally friendly refrigerant, SWEP plate heat exchanger, two type refrigeration system
5.Optimal structure and high efficiency refrigeration machinery design
6.Air intakes and returns with sensor control
7.Sever Valve, Kinetic energy automatic load control
8.Testing range: 150(60)℃~ (-10)-65℃
9.50% power saving efficiency and automatic servo control
10.Compatible with BUS CM remote monitoring management system
11.Can expanded: LN2V liquid nitrogen rapid cooling control device
12.Thermal shock test chamber movement time is 10 seconds.Can meet MIL, IEC and JIS standard.
13.Wind valve switching time is 10 seconds
14. Thermal shock test chamber temperature recovery time is 5 minutes, can meet the test specification
15.The end of the experiment, the product automatically return to the normal temperature to avoid frost dew
16.The world's first built-in USB2.0 interface digital recorder (recording can be plugged in at any time)
17.Industrial grade upright full-color touch multilingual programmable control system
18.The world's first standard shipping included USB2.0 and disk storage machine dual interface
19.The protective mechanism of return to normal temperature after the test is finished.
20.The world's first complete test curve analysis shows that there is no time limit.
Thermal shock test chamber Specification:
|Temperature||Temperature impact range||-65℃～150℃ （A:-45℃～150℃;B:-65℃～150℃；)|
|Low temperature |
|25.0℃～-75.0℃ Within 60 mins |
|High temperature |
|25.0℃～150.0℃ Within 45 mins 3.0～7.0℃/min|
|Temperature conversion time||3s|
|Temperature recovery time||Within 5 mins|
|Material / |
|Internal material||Stainless steel(SUS304)|
|External material||Cold rolled steel sheet / powder spraying|
|Heat insulating material||100mm thickness polyurethane plate＋10mm |
thickness mineral wool
|Condenser||Air cooling, water cooling|
|Evaporator||Fin - and - Tube Heat Exchanger|
|Heater||Nickel chromium alloy heating wire|
|Size|| Interior size(mm) |
|Outer size(mm) |
|Operating ambient temperature||+5 ~ 35℃|
|Power supply||380V AC 50/60Hz|
|Controller||SANWOOD SH5600:Equipped with RS232， RS485 port；（7.0 inch controller) USB data export|
※Please consult the sales for specific technical parameters, SANWOOD reserves the right of explanation.
Guangdong Sanwood Technology Co.,Ltd